Daikin Remote Controller BRC1C61 Installationshandbuch PDF herunterladen (Seite 12)

10 English

NOTES

1. Shows only in case of protected pipes. Use H07RN-F in

case of no protection.

2. Insulated thickness : 1mm or more.

3. If the wiring is in a place where people it can be easily

touched by people, install an earth leakage breaker to pre-

vent electric shock.

4. When using an earth leakage breaker, make sure to select

one useful also to protection against overcurrent and short-

circuit.

When using an earth leakage breaker only for earth device,

make sure to use a wiring interrupter together.

•

The length of the transmission wiring and remote controller

wiring are as follows.

Length of the transmission wiring and remote controller wiring

9-3 ELECTRICAL CHARACTERISTICS

MCA: Minimum Circuit Amps (A) MFA:Max. Fuse Amps (A)

KW: Fan motor output (kW) FLA:Full Load Amps (A)

10. WIRING EXAMPLE

10-1 HOW TO CONNECT WIRINGS

•

Wire only after removing the control box lid as shown in

Fig. 17.

CAUTION

•

When clamping the wiring, use the included clamp material

(9) and (10) as shown in the Fig.17 to prevent outside pres-

sure being exerted on the wiring connections and clamp

firmly.

•

Be sure to attach power supply wiring and earth wire to the

control box with the clamp.

•

When doing the wiring, make sure the wiring is neat and

does not cause the control box lid to stick up, then close the

cover firmly. When attaching the control box lid, make sure

you do not pinch any wires.

•

Outside the air conditioners, separate the weak wiring (remote

controller and transmission wiring) and strong wiring (earth

wire and power supply wiring) at least 50 mm so that they do

not pass through the same place together. Proximity may

cause electrical interference, malfunctions, and breakage.

Outdoor unit – Indoor unit

Max. 1000m

(Total wiring length: 2000m)

Indoor unit – Remote controller Max. 500m

Units Power supply Fan motor

Model

Hz Volts

Voltage

range

MCA MFA KW FLA

20 · 25 · 32 PBVE

220-

240

Min.

198

Max.

264

0.8

0.062 0.6

20 · 25 · 32 PBVET

0.7 0.062 0.6

40 NBVE(T)

1.0 0.062 0.8

50 NBVE(T)

1.0 0.13 0.8

63 NBVE(T)

1.1 0.13 0.9

20 · 25 · 32 PBVE

60 220

Min.

198

Max.

242

0.9

0.062 0.7

20 · 25 · 32 PBVET

0.8 0.062 0.7

40 NBVE(T)

1.1 0.062 0.9

50 NBVE(T)

1.3 0.13 1.0

63 NBVE(T)

1.4 0.13 1.1

Power supply wiring

Earth wire

Control box lid

Wiring Diagram

Fig. 17

(Rear)

∗

Do not connect power

supply wiring here.

That may cause

malfunctions.

∗Transmission wiring

∗Remote controller wiring

Power supply wiring

Earth wire

Clamp (for prevent slippage)

Clamp (for fixing in place)

Clamp the wiring sheaths (accessory (10))

Match up the wiring sheath with

the fixing clasp with the clamping

material for preventing slippage on

the power supply side and clamp

(accessory (9)).

Clamp

Remove the clasp with screwdriver.

Let a wire go through the clasp,

and be sure to attach the clasp to

the control box.

Clamp

Inside

unit

Outside

unit

[How to adhere it]

Wire

(accsessory)

Sealing

material (12)

•

Make sure to let a wire go through a wire penetration area.

•

After wiring, seal the wire and wire penetration area to prevent

moisture and small creatures from the outside.

•

Wrap the strong and weak electric lines with the sealing

material (12) as shown in the figure below.

(Otherwise, moisture or small creatures such as insects from

the outside may cause short-circuit inside the control box.)

Attach securely so that there are no gaps.

Penetration area

01_EN_3PN09042-1A.fm Page 10 Friday, March 21, 2008 7:21 PM

1 2 ... 7 8 9 10 11 12 13 14 15 16 17

Kommentare zu diesen Handbüchern

Keine Kommentare

Daikin Remote Controller BRC1C61 Installationshandbuch Seite 12

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Split-System-Klimaanlagen Daikin Remote Controller BRC1C61