Daikin Remote Controller BRC1C61 Installationshandbuch PDF herunterladen (Seite 10)

8 English

Remove the control box lid. Connect the remote controller

and power supply (single-phase, 50 Hz 220-240 V or sin-

gle-phase, 60Hz 220V) respectively to the terminal block

and securely connect the earth also (as shown in the figure

below).

CAUTION

Securely clamp the cables with the clamps (9)(10) offered

as accessories as shown in Fig. 17 so that tension will not

be applied on the cable connection areas.

Confirm that the control box lid is closed before turning on

the power.

Remove the inspection lid.

Gradually pour approximately 1L of water from the inspec-

tion window into the drain pan to check drainage.

CAUTION

Be sure to prevent an external force from being exerted on

the float switch.

(This may cause breakage.)

Attach the inspection lid.

Perform the following operation using the remote controller,

and check drainage.

•

Select the inspection/test operation button “ ” using

the remote controller. The unit will engage the test oper-

ation. Press the operation selector button “ ”, and

select FAN OPERATION “ ”.

•

Press the ON/OFF button “ ”. (The indoor fan and

drain pump will operate.)

CAUTION

The fan will turn also at the same time. Take due care.

Do not touch the drain pump to prevent electric shock.

Make sure to use the remote controller in finishing the oper-

ation.

CAUTION

•

The connection opening on the drain piping may vary

depending on the model, so check the model name and use

the right method for that model.

•

Make sure all water is out before making the duct connection.

(1)

Install the drain piping.

•

Make sure the drain works properly.

•

The diameter of the drain piping should be greater than or

equal to the diameter of the connecting pipe (vinyl tube; pipe

size: 20 mm; outer dimension: 26 mm).

(not including the riser)

•

Keep the drain piping short and sloping downwards at a gra-

dient of at least 1/100 to prevent air pockets from forming.

(Refer to Fig. 14)

CAUTION

Water accumulating in the drain piping can cause the

drain to clog.

•

To keep the drain piping from sagging, space hanging

bracket every 1 to 1.5 m.

•

Use the drain hose (2) and the metal clamp (1). Insert the

drain hose (2) fully into the drain socket and firmly tighten the

metal clamp (1) with the upper part of the tape on the hose

end. Tighten the metal clamp (1) until the screw head is less

than 4 mm from the hose. (Refer to Fig. 15, 16)

•

The two areas below should be insulated because conden-

sation may form there causing water to leak.

•

Drain piping passing indoors

•

Drain socket

Referring the figure below, insulate the metal clamp (1) and

drain hose (2) using the included large sealing pad (5).

(Refer to Fig. 16)

In case of PBVET, NBVET type (without drain pump)

TEST

TRANSMISSION

WIRING

REMOTE

CNTRL

T1F1

FORCED

OFF

P2 F2P1 T2

TRANSMISSION

WIRING

REMOTE

CNTRL

T1F1

FORCED

OFF

P2 F2P1 T2

L N

Inspection window

Portable pump

Inspection lid

Refrigerant pipes

Bucket

Service drain hole

Drain outlet

(with rubber cap)

Indoor PCboard

(ASSY)

Terminal block

Remote controller

terminal connection

method

Power supply:

Single phase,

50 Hz, 220 V~

240V

Single phase,

60Hz, 220 V

Power terminal

connection

method

Drain socket

Refrigerant pipes

Connect the drain pipe after removing the rubber cap and

insulation tubing attached to the connection hole.

Central drain piping

(with a slope of at least 1/100)

Fig. 14

100mm

or more

Metal clamp (1)

Drain hose (2)

Tape

Fig. 15 Fig. 16

(accessory)

≤4mm

Large sealing

pad (5)

Metal clamp (1)

(accessory)

01_EN_3PN09042-1A.fm Page 8 Friday, March 21, 2008 7:21 PM

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16 17

Kommentare zu diesen Handbüchern

Keine Kommentare

Daikin Remote Controller BRC1C61 Installationshandbuch Seite 10

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Split-System-Klimaanlagen Daikin Remote Controller BRC1C61