Daikin FTXG25EVMAW Bedienungsanleitung

FTXG25EVMAW FTXG25EVMASFTXG35EVMAW FTXG35EVMASMODELSDAIKIN ROOM AIR CONDITIONEROperation Manual00_CV_3P166462-1.fm Page 1 Monday, October 3, 2005 7

9 To set the clock1. Press “CLOCK button”.is displayed.blinks.2. Press “TIMER setting button” to set the clock to the present time.Holding down “ ” o

10OPERATIONAUTO · DRY · COOL · HEAT · FAN OperationThe air conditioner operates with the operation mode of your choice.From the next time on, the air

11 To change the air flow rate setting5. Press “FAN setting button”.• Indoor unit quiet operationWhen the air flow is set to “ ”, the noise from the

12Adjusting the Air Flow DirectionYou can adjust the air flow direction to increase your comfort. To adjust the horizontal blade (flap)1. Press “SWIN

13 To start COMFORT AIRFLOW operation5. Press “COMFORT AIRFLOW button”.The flap orientation will change, preventing air from blowing directly on the

14POWERFUL OperationPOWERFUL operation quickly maximizes the cooling (heating) effect in any operation mode. You can get the maximum capacity. To sta

15OUTDOOR UNIT SILENT OperationOUTDOOR UNIT SILENT operation lowers the noise level of the outdoor unit by changing the frequency and fan speed on th

16INTELLIGENT EYE Operation“INTELLIGENT EYE” is the infrared sensor which detects the human movement. To start INTELLIGENT EYE operation1. Press “SEN

17“INTELLIGENT EYE” is useful for Energy SavingNotes on “INTELLIGENT EYE”CAUTION Energy saving operation• Change the temperature –2°C in heating /

18TIMER OperationTimer functions are useful for automatically switching the air conditioner on or off at night or in the morning. You can also use OFF

1CONTENTSREAD BEFORE OPERATIONSafety precautions ... 2Names of parts...

19 To use ON TIMER operation• Check that the clock is correct. If not, set the clock to the present time. (page 9.)1. Press “ON TIMER button”.is disp

20CARECare and CleaningCAUTION Indoor unit, Outdoor unit and Remote controller1. Wipe them with dry soft cloth. Front panel1. Open the front panel

211. Open the front panel. •Open the front panel by placing a finger on the panel tab on either side of the front panel and then secure it using the s

22NOTECheck Before a long idle period1. Operate the “FAN only” for several hours on a fine day to dry out the inside.• Press “MODE” button and select

23TROUBLE SHOOTINGTrouble ShootingThe following cases are not air conditioner troubles but have some reasons. You may just continue using it.These cas

24Please check again before calling a repair person.Check again.Case CheckThe air conditioner does not operate.(OPERATION lamp is off.)• Hasn’t a brea

25WARNING When an abnormality (such as a burning smell) occurs, stop operation and turn the breaker OFF.Continued operation in an abnormal condition m

26MEMO01_EN_3P166462-1.fm Page 26 Tuesday, September 20, 2005 5:08 PM

27MEMO01_EN_3P166462-1.fm Page 27 Tuesday, September 20, 2005 5:08 PM

28MEMO01_EN_3P166462-1.fm Page 28 Tuesday, September 20, 2005 5:08 PM

2READ BEFORE OPERATIONSafety precautions•Keep this manual where the operator can easily find them.•Read this manual attentively before starting up the

(0509)HT3P166462-1M05B04200_CV_3P166462-1.fm Page 2 Monday, October 3, 2005 7:50 PM

3•Do not block air inlets nor outlets. Impaired air flow may result in insufficient performance or trouble.•Do not stand or sit on the outdoor unit. D

4Names of parts Indoor Unit15141812131713462111657 8 910(With the panel closed)01_EN_3P166462-1.fm Page 4 Tuesday, September 20, 2005 5:08 PM

5 Outdoor Unit Indoor Unit1. Air filter2. Titanium Apatite Photocatalytic Air-Purifying Filter:• These filters are attached to the inside of the a

6 Remote Controller1. Signal transmitter:•It sends signals to the indoor unit.2. Display:• It displays the current settings. (In this illustration, e

7Preparation Before Operation To set the batteries1. Slide the front cover to take it off.2. Set two dry batteries (AAA).3. Set the front cover as be

8Preparation Before Operation To operate the remote controller• To use the remote controller, aim the transmitter at the indoor unit. If there is any